Stan dysku?

[dzagu]

Witam, czy na smarcie dysku wszystko jest okej?

root@mk249:~# smartctl -a /dev/sda
smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.9.0-6-amd64] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Seagate Barracuda 7200.14 (AF)
Device Model:     ST1000DM003-1SB10C
Serial Number:    Z9A0DFQ0
LU WWN Device Id: 5 000c50 08754ed3e
Firmware Version: CC43
User Capacity:    1 000 204 886 016 bytes [1,00 TB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    7200 rpm
Form Factor:      3.5 inches
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA8-ACS T13/1699-D revision 4
SATA Version is:  SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is:    Wed Sep 19 20:56:03 2018 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x82) Offline data collection activity
                                        was completed without error.
                                        Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0) The previous self-test routine completed
                                        without error or no self-test has ever
                                        been run.
Total time to complete Offline
data collection:                (    0) seconds.
Offline data collection
capabilities:                    (0x7b) SMART execute Offline immediate.
                                        Auto Offline data collection on/off support.
                                        Suspend Offline collection upon new
                                        command.
                                        Offline surface scan supported.
                                        Self-test supported.
                                        Conveyance Self-test supported.
                                        Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        General Purpose Logging supported.
Short self-test routine
recommended polling time:        (   1) minutes.
Extended self-test routine
recommended polling time:        ( 111) minutes.
Conveyance self-test routine
recommended polling time:        (   2) minutes.
SCT capabilities:              (0x1085) SCT Status supported.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   078   063   006    Pre-fail  Always       -       78391133
  3 Spin_Up_Time            0x0003   098   098   000    Pre-fail  Always       -       0
  4 Start_Stop_Count        0x0032   100   100   020    Old_age   Always       -       9
  5 Reallocated_Sector_Ct   0x0033   100   100   010    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x000f   080   060   045    Pre-fail  Always       -       8824361008
  9 Power_On_Hours          0x0032   080   080   000    Old_age   Always       -       18368
 10 Spin_Retry_Count        0x0013   100   100   097    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   020    Old_age   Always       -       8
183 Runtime_Bad_Block       0x0032   099   099   000    Old_age   Always       -       1
184 End-to-End_Error        0x0032   100   100   099    Old_age   Always       -       0
187 Reported_Uncorrect      0x0032   100   100   000    Old_age   Always       -       0
188 Command_Timeout         0x0032   099   098   000    Old_age   Always       -       6 6 7
189 High_Fly_Writes         0x003a   100   100   000    Old_age   Always       -       0
190 Airflow_Temperature_Cel 0x0022   064   055   040    Old_age   Always       -       36 (Min/Max 33/38)
193 Load_Cycle_Count        0x0032   100   100   000    Old_age   Always       -       771
194 Temperature_Celsius     0x0022   036   014   000    Old_age   Always       -       36 (0 14 0 0 0)
195 Hardware_ECC_Recovered  0x001a   007   001   000    Old_age   Always       -       78391133
197 Current_Pending_Sector  0x0012   100   100   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0010   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x003e   200   200   000    Old_age   Always       -       0
240 Head_Flying_Hours       0x0000   100   253   000    Old_age   Offline      -       18368h+10m+08.144s
241 Total_LBAs_Written      0x0000   100   253   000    Old_age   Offline      -       24424407494
242 Total_LBAs_Read         0x0000   100   253   000    Old_age   Offline      -       5114335476

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
No self-tests have been logged.  [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

 

[theqkash]

Teoretycznie tak, w praktyce natomiast te dwie wartości:
 

Godzinę temu, dzagu napisał:

7 Seek_Error_Rate 0x000f 080 060 045 Pre-fail Always - 8824361008

 

Godzinę temu, dzagu napisał:

195 Hardware_ECC_Recovered 0x001a 007 001 000 Old_age Always - 78391133

nie wróżą raczej nic dobrego...

[Vescer]

Po czasie pracy i ilości włączeń widać iż pracuje on w serwerze. Generalnie jest okay poza tym co @theqkash napisał. Sam osobiście mam ST1000DM003 który pracuje jako magazyn danych w moim komputerze i nie mogę złego słowa powiedzieć. Po prawie 12k godzin mam zdecydowanie dużo niższe wartości Seek_Error_Rate i Hardware_ECC_Recovered, ale zakładając że u ciebie jest to podstawowy dysk na którym wszystko pracuje to te dwa wyniki takie mogą być.

[Poziomecki]

To je sigejt. Tam 01 i 07 nie bangla